There are eight common types of roof insulation: mineral wool rolls, blown loose-fill, rigid PIR boards, insulated plasterboard, natural fibre (sheep's wool and wood fibre), multifoil, spray foam and warm-deck flat-roof boards. For most Scottish homes with an open loft, mineral wool rolled out to 270 mm is still the cheapest and simplest choice. The others earn their place where the loft is boarded, lived in, sloped or flat.
Choosing between the eight is really a choice about where the heat is escaping and what your loft or flat roof can physically take. Our roof insulation installers survey the build-up before recommending a material, and the full roof insulation types comparison sets out U-values, depths and typical costs side by side.
Which roof insulation type do you need? Start with the roof, not the material
The type of roof decides the shortlist before price does. Four situations cover nearly every house in the Central Belt:
- An open, unboarded loft (most semis, bungalows and post-war houses): insulate at ceiling level, between and over the joists. This is a "cold roof" and the loft stays cold above the insulation.
- A loft you want to use or store in: you either raise the floor on legs above the insulation or insulate at rafter level instead, which makes the loft a "warm roof".
- A room in the roof (dormer bungalows, many 1930s and Victorian homes): the sloping ceilings, the short stud walls and the flat ceiling section above each need their own treatment.
- A flat roof (extensions, garages, some 1960s and 1970s houses): insulation is best fitted on top of the deck under a new waterproof layer, known as a warm deck.
Once you know which of the four you have, the eight types below sort themselves into "suits my roof" and "doesn't".
1. Mineral wool rolls (glass wool or rock wool)
Rolls of glass or rock mineral wool laid between the ceiling joists, with a second layer at right angles over the top, are the default loft insulation in the UK. The Energy Saving Trust's recommended depth is 270 mm, and the energy rating software behind every EPC (RdSAP 10) recommends a loft top-up wherever the existing layer is 150 mm or less, using the same 270 mm standard.
It is cheap, non-combustible and easy to lay. The catches: it must not be squashed by boxes or boarding, and it must leave the eaves open so the roof space can still ventilate.
2. Blown loose-fill insulation
Loose mineral wool or cellulose fibres blown into the loft through a hose. It fills awkward joist spacings, low eaves and lofts with poor access better than rolls do, because nobody has to crawl into the tight corners. It suits the same cold-roof lofts as rolls and is a common choice for topping up an existing thin layer.
3. Rigid PIR insulation boards
Foil-faced polyisocyanurate (PIR) boards give the most insulation per millimetre of the common materials, which is why they are used where depth is limited: between and under rafters in a warm-roof loft conversion, on flat roofs, and on the sloping ceilings of a room in the roof. They cost more per square metre than mineral wool and need careful cutting and taping to avoid gaps, which is where most of the heat loss in a board installation happens.
4. Insulated plasterboard
Plasterboard with a layer of PIR or similar bonded to the back. It is fixed to the underside of rafters or to sloping ceilings, so the insulation and the new ceiling go up in one job. It is the usual route for room-in-roof upgrades where the ceilings are coming down anyway, and for topping up between-rafter boards without losing much headroom.
5. Natural fibre: sheep's wool and wood fibre
Sheep's wool rolls and wood-fibre batts or boards do the same job as mineral wool, with two differences people choose them for: they are pleasant to handle, and they hold and release moisture, which suits older solid-stone and timber buildings that need to "breathe". They cost more than mineral wool for the same performance, so they tend to be chosen for the building, not for the price.
6. Multifoil insulation
Thin layers of reflective foil and wadding, a few centimetres thick, stapled across rafters. Its appeal is saving headroom. Its performance depends on air gaps either side and on the specific product, so ask for the product's certified figures before relying on it. It is most often used alongside boards rather than on its own.
7. Spray foam insulation
Foam sprayed onto the underside of the roof between the rafters. It is quick to fit and seals gaps, but it covers the rafters and the underside of the slates, which makes any later inspection or repair of the roof harder, and it is difficult to remove. If you are offered spray foam, ask how the roof timbers will be ventilated and inspected afterwards, and check with your mortgage lender before you agree.
8. Warm-deck flat-roof boards
On a flat roof the insulation goes on top of the existing deck, under a new waterproof covering, so the timber deck stays warm and dry. It is usually done when the roof covering is due for replacement, because the covering has to come off anyway. Insulating a flat roof from underneath (a cold deck) risks condensation in the timbers and is avoided where a warm deck is possible.
Roof insulation types compared
The table sums up where each type goes and what it is best at. For costs per square metre and U-values side by side, see our roof insulation types compared page.
| Type | Where it goes | Best for | Watch out for |
|---|---|---|---|
| Mineral wool rolls | Between and over loft joists | Open lofts; lowest cost | Squashing by boards or boxes; blocked eaves |
| Blown loose-fill | Loft floor, blown in | Awkward or low lofts; top-ups | Needs boarding kept clear of it |
| Rigid PIR boards | Between or under rafters; flat roofs | Warm roofs where depth is tight | Gaps at joints if not taped |
| Insulated plasterboard | Under rafters, sloping ceilings | Room-in-roof upgrades | Some headroom lost |
| Sheep's wool / wood fibre | Loft joists or rafters | Older stone and timber homes | Higher price per unit of insulation |
| Multifoil | Across rafters | Saving headroom | Needs air gaps; check certified figures |
| Spray foam | Under the roof between rafters | Fast sealing of gaps | Hides timbers; hard to remove; ask your lender |
| Warm-deck boards | On top of a flat-roof deck | Flat roofs being re-covered | Done with a new waterproof layer |
What roof insulation costs, and what it saves
The Energy Saving Trust puts a professionally installed loft top-up to 270 mm at about £750 for a loft with no insulation and about £600 where 120 mm is already there. The Trust's figures show that topping up an existing 120 mm layer saves far less each year than insulating an empty loft, so the big gains come from lofts with little or nothing in them.
Insulation also lifts an EPC. Propertymark's analysis of EPC scores puts standard loft insulation at about 4.9 points on average and room-in-roof insulation at about 9.91, one of the most effective single measures it studied. That matters if you let the property or plan to sell.
Installation of insulation in a home is currently zero-rated for VAT in Great Britain, so a quote for fitted insulation should not add VAT.
Grants for roof insulation in Scotland
Home Energy Scotland's grant and loan funds insulation for homeowners living in the property. Its table (read 6 October 2026) lists up to £1,500 grant plus up to £500 loan for loft insulation, and up to £3,000 grant plus up to £1,000 loan for flat-roof or room-in-roof insulation, with a £1,500 uplift for rural and island homes. Funding is first come, first served each financial year, and work must not start before the written offer arrives. You apply through Home Energy Scotland yourself. Our solar panel grants in Scotland guide sets out what else is open.
The Great British Insulation Scheme closed to new installations on 31 March 2026. ECO4 runs until 31 December 2026 for households on qualifying benefits, but the energy supplier decides each case, so treat it as a possibility rather than a plan.
What the roof insulation regulations actually require
This is the question the search results keep asking and mostly answer badly, so here is the short version for a Scottish house.
Depth, not product. The figure that matters for a loft is depth. The Energy Saving Trust puts the current building-regulations minimum for mineral wool at 270 mm (guidance last updated 8 May 2026). Older houses were often done to 100 mm or 120 mm and never topped up, which is why so many lofts look insulated and still lose heat.
Building standards are devolved. Scotland sets its own building standards and England sets its own, so a depth or U-value quoted from an English guide is not automatically what your Scottish building warrant will be judged against. If the work needs a warrant, the standard that applies is the one in force for your council when the application goes in, so ask the installer which one they are designing to and get the answer in writing.
Topping up counts as the baseline, not as the upgrade. Under the ECO4 rules, insulation already in place that sits below current building regulations has to be topped up as part of the job and cannot itself be counted as the funded measure (Ofgem, ECO4 Guidance: Delivery v4.0, 26 March 2026, sections 5.58 to 5.65). In practice a 120 mm loft is not finished for funding purposes.
And one scheme people still ask for by name. The Great British Insulation Scheme ended on 31 March 2026 and is closed to new installations (Ofgem). If a company is still offering it, that tells you something about the company.
If you want the installation side rather than the materials, our roof insulation installers page covers the survey, the fitting and the ventilation detail that decides whether a warm roof stays dry.
Insulate the roof before you add solar or a heat pump
Cutting heat loss first means a smaller heat pump will do the job, and the electricity your panels make goes further. If a heat pump is on your list, insulation and the heat pump can both be funded through Home Energy Scotland in the same year. See air source heat pumps in Scotland and our solar panel installation page for the next steps once the roof is done.
Roof insulation questions, answered
What is the best type of roof insulation?
For an open loft, mineral wool laid to 270 mm is the best value and the depth the Energy Saving Trust recommends. Where the loft is used, the ceiling slopes or the roof is flat, rigid PIR boards or insulated plasterboard usually work better because they give more insulation in less depth.
How thick should loft insulation be?
The recommended depth is 270 mm of mineral wool. The software that produces EPCs recommends a top-up wherever the existing insulation is 150 mm or less.
Is there a grant for roof insulation in Scotland?
Yes. Home Energy Scotland lists up to £1,500 grant plus up to £500 loan for loft insulation and up to £3,000 grant plus up to £1,000 loan for flat-roof or room-in-roof insulation (6 October 2026), with a £1,500 rural and island uplift. Funding is limited each financial year and you must wait for the written offer before work starts.
Is spray foam roof insulation a good idea?
It can seal a roof quickly, but it covers the rafters and the underside of the slates, which makes later inspection and repair harder and is difficult to undo. Ask how the timbers will be ventilated and check with your mortgage lender before agreeing to it.
Does roof insulation improve my EPC?
Usually. Propertymark's analysis puts standard loft insulation at about 4.9 EPC points on average and room-in-roof insulation at about 9.91.
Every property is different. Get a personalised consultation — free and no-obligation.
Free quote →